Versions Compared

Old Version 99

changes.mady.by.user Nicolas Stifani

Saved on

compared with

New Version Current

changes.mady.by.user Nicolas Stifani

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Include Page
_Micro-head-en
_Micro-head-en

Button Hyperlink
iconbuild
titleFrançais
typeprimary
urlZeiss Z1 Colibri

Zeiss Z1-Colibri Microscope

Desmarais Building, Room 2234
Simple Microscope usage price
Instrument awarded to Dr. Audrey Claing and Dr. Jean-Philippe Gratton by the Canadian Foundation for Innovation (CFI) in 2014

 

Applications

  • Inverted microscope
  • Widefield imaging
    • Brightfield
    • Phase contrast
    • Fluorescence
  • Incubation
  • Timelapse imaging
  • Deconvolution
  • Extended Depth of Focus

Image Added

Tabs Container
directionhorizontal
Tabs Page
idDescription
titleDescription

Description

Light sources

  • LED lamp for transmitted light

  • Colibri 7 R[G/Y]B-UV (385/469/555-590/631) for fluorescence
Expand
titleComplete specifications

Emission peak (nm)

Nominal Power (mW)Measured Power (mW)
385/30150 
469/38110 
555/3031 
631/3350 

View file
nameZeiss_Colibri-7_Product Information.pdf
height250

Objectives

  1. 2.5x/0.075 Air

  2. 10x/0.25 Air Ph1
  3. 20x/0.5 Air Ph2

  4. 40x/0.75 Air Ph2

  5. 63x/0.75 Air Ph2 Long Distance
  6. 63x/1.4 Oil
Expand
titleComplete specifications
PositionNameBrandFull nameIDMagnificationNumerical ApertureImmersionTypeWorking distance (mm)Transmittance
(% [nm])		TechniqueCover glass thickness (mm)
12.5x/0.075 AirZeiss2.5x/0.075
EC Plan-Neofluar		420320-9901-0002.5x0.075AirPlan Neofluar9.5>80% [400-840]BF, Fluo0.17
210x/0.25 AirZeiss10x/0.25 Ph1
N-Achroplan		420941-9911-00010x0.25AirN-AchroPlan

6.5

Not AvailableBF, PhC, Fluo0.17
320x/0.5 AirZeiss20x/0.50 Ph2
EC Plan-Neofluar

420351-9910-000

20x0.50AirPlan Neofluar2.0Not AvailableBF, PhC, Fluo0.17
4

40x/0.75 Air

Zeiss40x/0.75 Ph2
EC Plan-Neofluar

420361-9910-000

40x

0.75

Air

Plan Neofluar0.71Not AvailableBF, PhC, Fluo

0.17

563x/0.75 Air
Zeiss

63x/0.75 Corr Ph2
LD Plan-Neofluar

421381-9970-000

63x

0.75

AirLD Plan-Neofluar1.7 at cover glass 0.75Not AvailableBF, PhC, Fluo

0 - 1.5

663x/1.4 OilZeiss63x/1.4 DIC
 Plan-Apochromat Oil		420782-9900-00063x1.4OilPlan Apochromat0.19>80% [400-700]BF, Fluo0.17

Filter

  1. DAPI
  2. GFP
  3. Rhodamine
  4. DHE (dihydroethidium)
  5. Cy5
  6. Quadruple DAPI/GFP/Cy3/Cy5
Expand
titleComplete specifications
PositionNameBrandIDExcitation filterDichroic mirrorEmission filterComments
1DAPI
Filter Set 49		Zeiss

488049-9901

365/50
[325-375]		395LP445/50
[420-470]
2GFP
Filter Set 13		Zeiss488013-0000

470/20
[460-480]

495LP

517/25
[505-530]
3DsRed
Filter Set 43		Zeiss

000000-1114-101

545/25
[533-567]		570LP605/70
[570-640]
4DHECustom

Custom

500/50
[475-525]

540LP580/20
[570-590]		Undefined specifications
Best guess values
5Cy5
Filter Set 50		Zeiss488050-9901640/30
[625-655]		660LP

690/50
[665-715]


6Quadruple
DAPI/GFP/Cy3/Cy5
FS90 HE LED		Zeiss489090-9110-000


QBS
405+493+575+653

QBP 425/30+514/30+592/25+709/100

Excitation filters included in the light source FS90 HE LED

Detectors

  • PCO Edge 5.5
    Expand
    titleComplete specifications
    CameraPCO Edge 5.5

    Sensor Type

    		sCMOS

    Sensor Category

    		Monochrome

    Nb Pixels

    		5.5 M

    Pixel Layout

    		2560 x 2160

    Pixel size

    		 6.5 um

    Sensor size

    		16.6 mm x  14.0 mm

    Sensor diameter

    		21.8 mm

    Bit depth

    		16-bit
    Speed at full resolution100 images/s

    Max QE

    		 60 % at 600 nm
    Reading noise 1.0 e⁻

    Cooling

    		Forced air +7C

    Dark Current

    		0.6 e⁻/pixel/sec

    Full well capacity

    		30 000 e-

    Dynamic Range

    		1:30000

    Interface

    		Dual Camera Link PCIe

    Mount

    		C-mount

    View file
    namePCO_Edge 5.5_Datasheet.pdf
    height250

  • Zeiss Axiocam MRm (not installed)
Expand
titleComplete specifications
CameraZeiss Axiocam MRm

Sensor Type

CCD

Sensor Category

Monochrome

Nb Pixels

1.4 M

Pixel Layout

1388 x 1040

Pixel size

 6.45 um

Sensor size

8.9 mm x 6.7 mm

Sensor diameter

11 mm

Bit depth

12-bit
Speed at full resolution13 images/s

Max QE

 55 %
Readout noise 8 e⁻

Cooling

Pelletier

Dark Current

0.7 e⁻/pixel/sec

Full well capacity

17 000 e-

Dynamic Range

1:2000

Interface

FireWire (IEEE 1394a)

Mount

C-mount


View file
nameZeiss_AxioCam MRm_Datasheet.pdf
height250

Tabs Page
idUser Guide
titleUser Guide

User Guide

UI Expand
expandedtrue
titleStartup
  1. If not already done, turn on the computer (#1) and log in to Windows using your UdeM credentials
  2. Remove the dust cover from the microscope
  3. If incubation is required, turn on the incubation power bar (#2) on the desk near the computer and open the CO₂ cylinder (#2B) near the sink
    Note

    Make sure the humidifier is properly filled with distilled water.

  4. Turn on the microscope power bar (#3) on the desk near the computer

  5. When using the instrument for the first time, it is necessary to import the microscope configuration before starting the software. See the First Use section below.
  6. Start Zen
UI Expand
titleFirst Use

When using the instrument for the first time, it is necessary to import the microscope configuration into the software. This procedure is usually carried out during the training session. However, it can also be used to reset the software if it does not display correctly, for example. Running this procedure will erase all your experiment protocols and reset the software to its original settings (ask for support if you are not sure).

  1. If Zen is open, close it and wait until it has completely shut down (this may take up to 30 seconds)

  2. On the Desktop, open the Softwares folder

  3. Double-click Zen Settings for Zeiss Z1-Colibri

  4. A script will run and a black window will appear briefly

  5. When the message Settings for Zen have been imported successfully appears, click OK to close it

  6. You can now open Zen

UI Expand
titleLoading samples

During this procedure, you will:

  • Set the microscope to a safe configuration
  • Perform a calibration
  • Load your sample
  • Find and adjust the focus

Once completed, your sample will be ready for acquisition.

UI Expand
titleCalibration

This step is required to calibrate the microscope in XY and Z. Performing this calibration will significantly reduce the time needed to locate and focus on your sample.

  • If not already done, select the lowest-magnification objective. On the microscope touch screen Home > Microscope > Control > Objectives > 2.5x
  • In Zen, once it has started a calibration dialog should appear. Simply click Calibrate Now.
    The microscope will lower the objectives, perform an XY calibration first, followed by a Z calibration, and then return to its original position.
Tip

Once calibrated, the focus is typically found at Z = 1.1 mm for a microscope slide. For a multi-well plate the focus is generally around Z = 3 mm but this is highly dependent on your multi-well plate.
The Z position can be viewed on the microscope touch screen under Home > Z-Position, as well as in Zen within the Focus tab, located on the right side of the screen.

Expand
titleThe calibration dialog did not appear...

The system may already be calibrated. This can occur if a previous user calibrated the system and left it on.

UI Expand
titleVerifying if the system is already calibrated

In Zen, within the Focus tab, located on the right side of the screen:

  1. Click Load to lower the objective

  2. The Z position is indicated below Current
  3. If Z position value is less than 100 um the system is calibrated

On the microscope touch screen:

  1. Lower the objective by pressing Home > Load Position

  2. Press Set Work Position to store this position

  3. If necessary, slightly adjust the focus upward to clear the Lower Z Limit Reached message displayed on the touch screen

  4. The Z position value is indicated
  5. If the value is less than 0.1 mm then the system is calibrated
UI Expand
titleManual calibration with the software

In Zen, within the Stage tab, located on the right side of the screen:

  1. If not already done, check the Show All option

  2. At the bottom of the tab click Calibrate

  3. A warning message will show up click Continue

  4. The microscope will lower the objectives and perform a XY stage calibration and then return to its original position.

In Zen, within the Focus tab, located on the right side of the screen:

  1. If not already done, check the Show All option

  2. At the bottom of the tab click Calibrate

  3. A warning message will show up click Continue

  4. The microscope will then perform a Z calibration and then return to its original position

XY and Z calibrations are now complete

UI Expand
titleManual calibration with the microscope touch screen

On the microscope touch screen:

  1. Navigate to Home > Microscope > XYZ > Position > Z-Position > Set Zero > Auto to perform focus calibration

  2. Press OK to start the calibration procedure

  3. Wait a few seconds for the calibration to complete

  4. Lower the objective by pressing Home > Load Position

  5. Press Set Work Position to store this position

  6. If necessary, slightly adjust the focus upward to clear the Lower Z Limit Reached message displayed on the touch screen

  7. Navigate to Home > Microscope > XYZ > Position > XY-Position > Set Zero > Auto to perform a stage calibration

  8. Press OK to start the calibration procedure

  9. Wait a few seconds for the calibration to complete

XY and Z calibrations are now complete

UI Expand
titleEnsuring the calibration dialog is displayed at startup

In Zen:

  1. In the menu bar, navigate to Tools > Options

  2. Select Startup/Shutdown

  3. Under Stage/Focus Calibration, ensure Request Stage/Focus Calibration on Startup is checked

  4. Click OK to close the Options dialog

UI Expand
titleInitial focus
Warning
titleImportant
Ensure that the calibration has been completed beforehand. Calibration will significantly reduce the time required to locate and focus on your sample.

On the microscope touch screen:

  1. If not already done, select the lowest-magnification objective Home > Microscope > Control > Objectives > 2.5x
Info

The 2.5× and 10× objectives are the safest to use due to their long working distance (>6 mm). The sample will appear in sharp focus well before the objective approaches it. It is recommended to always focus using the safest objectives first. Since the objectives are parafocal, focusing with the safest objectives will facilitate locating the sample when switching to higher-magnification objectives.

  1. Lower the objective by pressing Home > Load Position

  2. Press Set Work Position to store this position

  3. If necessary, slightly adjust the focus upward to clear the Lower Z Limit Reached message displayed on the touch screen

  4. Place the test slide on the microscope stage with the coverslip facing the objective
    Note
    titleImportant

    Using a test slide will significantly reduce the time required to set up the instrument.

  5. If necessary, adjust the stage to ensure that the sample is centred under the objective

In Zen:

  1. In the Locate tab, select BF or the desired fluorescence (Fluo, DAPI, GFP, Cy3, Cy5) to activate the configuration
  2. Adjust the focus with the main dial while looking through the eyepieces until the image is perfectly sharp
Info

Once calibrated, the focus is typically found at Z = 1.1 mm for a microscope slide. For a multi-well plate the focus is generally around Z = 3 mm but this is highly dependent on your multi-well plate.
The Z position can be viewed on the microscope touch screen under Home > Z-Position, as well as in Zen within the Focus tab, located on the right side of the screen.

  1. In the Locate tab, select Off to turn off the illumination
UI Expand
titleSeconday focus
Warning
titleImportant

Perform the initial focus using the safest objective before switching to higher-magnification objectives.

UI Expand
titleFocusing with air objectives

After performing the initial focus, on the microscope touch screen:

  1. Press Home>Microscope>Control>Objectives
  2. Press 10x, 20x, 40x or 63x (0.75) to select the desired objective
Info
The 40x objective is the best Air objective because it has the largest Numerical aperture (0.75) together with a wider field of view (40x).

In Zen:

  1. In the Locate tab, select BF or the desired fluorescence (Fluo, DAPI, GFP, Cy3, DsRed, Cy5) to activate the configuration
  2. Adjust the focus with the precision dial while looking through the eyepieces until the image is perfectly sharp
  3. In the Locate tab, select Off to turn off the illumination

Your sample is ready for acquisition!

UI Expand
titleFocusing with oil objectives

After performing the initial focus, on the microscope touch screen:

  1. Press Home>Microscope>Turret>Objectives

  2. Press 63x Oil (1.4)to select the desired objective. The microscope will automatically lower the stage so that the sample becomes accessible.

  3. Place a single drop of oil on the objective
  4. Press Done. The microscope will automatically return the objective to its original position

In Zen :

  1. In the Locate tab, select BF or the desired fluorescence (Fluo, DAPI, GFP, Cy3, DsRed, Cy5) to activate the configuration
  2. Adjust the focus with the precision dial while looking through the eyepieces until the image is perfectly sharp
  3. In the Locate tab, select Off to turn off the illumination

Your sample is ready for acquisition!

UI Expand
titleStorage management
  • Files can be saved temporarily (during acquisition) on the local C: drive (desktop)
  • At the end of each session, copy your data to your external drive and delete it from the local C: drive
  • You can store your files on the D: drive (Data Storage). If you do, please create a folder per laboratory using the principal investigator last name. Within, create one folder per user (Firstname_Lastname).
Note

In any case, your files should be removed from the C: drive.

UI Expand
titleShutdown
  1. Save your data
  2. Close Zen
  3. Transfer your data to the D: drive (Data Storage) or to your external drive and delete it from the local C: drive
  4. If used, clean oil objectives with lens cleaner and paper
  5. Select the lowest magnification objective and press load position to place the objectives in a safe position

  6. If used, turn off the incubation module power strip (#2A) and close the CO2 cylinder (#2B)

  7. Turn off the microscope power bar (#3)

  8. Turn off the computer
  9. Cover the instrument with the protective dust cover
Note
titleReminder
  • Take back your samples including ones in the microscope
  • Leave the microscope and the working area clean

Tabs Page
titleLog

Log

UI Expand
titleTo be done
  • Measure Power output
  • Modify camera power supply cable
UI Expand
title2025-10-22 Windows 11 and more
  • Installation of Windows 11
  • Added CO2 connection to incubation module
  • Cable management
  • Replaced video card
UI Expand
title2025-09-01 Camera upgrade
  • Added compressed air connexion to the anti-vibration table
UI Expand
title2025-09-01 Camera upgrade
  • AxioCam replacement with PCO Edge 5.5
UI Expand
title2025-08-21 Wiki Updated
  • Updated wiki with complete specifications
UI Expand
title2024-02-22 Microscope Firmware update
  • Microscope Firmware update to add Colibri to the touchscreen
  • Zen 3.5 HotFix 10
UI Expand
title2022-05-09
  • Computer replacement
  • Added Colibri
  • Added startup procedure
  • Parafocality and paracentrality
UI Expand
title2022-03-17
  • Added complete description
UI Expand
title2021-09-27
  • Added to wiki
Tabs Page
titleTechnical Datasheet

Technical Datasheet

Stand

  • Zeiss Axio-Observer Z1 inverted Serial: 3851001242 Part Number: 431007-9902-000
    System ID: 1024979772

  • Camera adapter Model 60N-C, 1", 1x, Model: 426114

Light sources

  • Transmitted LED light
  • Colibri 7 R(G/Y)B-UV 423052-9730-000 Serial 5440000661

Condenser

  • Manual condenser

  • Lens NA 0.35 WD 70 mm Part Number: 424241

  • Filter turret 6 positions manual

    1. H

    2. Ph0

    3. Ph1

    4. Ph2

    5. DIC

    6. DUC

Objectives

  1. 2.5x/0.075 Air 420320-9901-000

  2. 10x/0.25 Air Ph1 420941-9911-000

  3. 20x/0.5 Air Ph2 420351-9910-000

  4. 40x/0.75 Air Ph2 420361-9910-000

  5. 63x/0.75 Air Ph2 Long Distance 421381-9970-000

  6. 63x/1.4 Oil 420782-9900-000

Stage

  • Motorized stage Marzhauser Scan IM 130x100-2mm 90-24-550-0000 Serial 16053038
    Stage Controller 90-76-024-1803 Serial 14 04 1 2040 SMC 2009 432929-9011-000
  • Remote control joystick 2-Axis 90-76-200-0820 Zeiss Article 432903-9011-000 Serial 1615142059
  • Inserts
    • Slide combo
    • Multi-well plate

Filters

  1. DAPI Filter Set 49 488049-9901
  2. GFP Filter Set 13 488013-0000
  3. Rhodamine Filter Set 43 000000-1114-101
  4. DHE (dihydroethidium) 424931
  5. Cy5 Filter Set 50 488050-9901
  6. Multiband FS90 HE LED 489090-9110-000

Detector

  • Zeiss AxioCam MRm Model: r3.1 Part Number: 426509-9901-000. Serial: 1 22 12 5537
  • PCO Edge 5.5 Model pco.API.Air.BX Serial 6000001404

Workstation

  • Computer
    • Fujitsu Esprimo P920 E90+ Model MI5W Serial YLPS036541
  • Motherboard
    • Fujistsu D3222-A1 (1 PCIe Gen3 x16, 1 PCIe Gen 2 x16 (x4 lanes), 2x PCIe Gen2 x1
    • Chipset Intel Q87
    • BIOS UEFI compatible American Trend v4.6.5.4 R1.47.0 for D3222-A1x 2019-08-26 
  • Processor
    • Intel Core i5-4670 @ 3.4 GHz
  • RAM
    • 24 GB DDR3 800 MHz (3 x 8 GB)
  • OS Drive
    • 1 TB SSD 550 MB/s
    • Win 11 23H2
  • Storage
    • 2 TB HD 110 MB/s
  • Video Card
    • AMD FirePro V4900 1 GB DDR5 0.768 TFLOPS 1x PCIe gen2 x16
  • Monitor
    • LG Flatron E2711 27' 1920 x 1080
    • LG W2442 1920 x1080
  • Software
    • Zen Blue 3.5
    • Serial 1121159628-524292
    • HASP 1798977001
    • Extended Focus
    • Measurements
    • Multi-Channel
    • Panorama
    • Software autofocus
    • Time Series
    • Z-stack 

Incubation

  • Pecon stage top incubation

Anti-vibration table

  • TMC Model 63 512 Serial 933240
  • Plain table top

Consumables

  • CO2 Tank
  • Oil
  • Lens Cleaner

Manuals

Tabs Page
titleTroubleshooting & FAQ

Troubleshooting

UI Expand
titleI don't see any fluorescence!

Technical support is free and unlimited. Contact us !

UI Expand
titleI see a high background in fluorescence

This happens in the following conditions at

  • At 2.5x using the DAPI or GFP channel
  • At 10x using the GFP channel
  • At 20x using the GFP channel

 To solve this you can use any of the following option:

  • Tilt the transmitted light arm backward
  • Close the manual shutter between the condenser and the transmitted light
  • Use a higher magnification objective

FAQ

UI Expand
titleCan I use this microscope to look at cell in a dish?

Yes. This is an inverted microscope designed to look at specimen in a dish or a multi-well plate. The objectives are optimized to image through thin glass bottom multi-well plates. You may also image specimen mounted between a slide and a 0.17mm thick coverslip. For long timelapse, be aware of photo-toxicity.

UI Expand
titleCan I use this microscope to perform timelapse experiments?

Yes, but... This microscope has an incubation module to maintain temperature, humidity and gas. Yet it does not have a Definite focus which can maintain focus throughout time. Therefore, it is possible to loose the focus over long period. You can always do a software autofocus at different time but be aware of photo-toxicity if you are using fluorescence.

UI Expand
titleWhat is Extended Depth of Focus?

Extended Focus is a method to flatten a Z-stack by keeping only the relevant information.

In Zen:

  • Select the Processing Tab
  • Select the Extended Depth of Focus Method
  • Click Apply
  • Wait until the processing is finished
  • Save the processed image

Z Stack animationMaximum Intensity projection of a Z-StackExtended Depth of Focus projection of a Z-Stack

Include Page
Plateformes:_Plat-foot-en
Plateformes:_Plat-foot-en